Seat Alhambra Key Problems
Seat's family MPV jumbo is among the top in class when it comes to maintaining resale value. With a new model currently on sale the family MPV jumbo is more impressive.
There are a myriad of reasons that the key fob may not function correctly, including dead battery, water damage, receiver module problems or signal interference. This article will walk you through the steps needed to get it working again.
Water Damage
If your key fob for the seat alhambra can withstand a wash cycle or a dip in the ocean or a pool then it's equipped with a waterproof chip. But don't do this often as excessive exposure to water increases the chance of the key fob getting damaged. If the key fob stops working after exposure to clean water from the tap or rain, just take out the battery, clean the electronic component using a paper towel and let it dry completely before putting the battery back in. If the battery is exposed to soapy or salty water, it is recommended to wash the chip using isopropyl alcohol or a electronic cleaner before attempting to put the battery back in.
Faulty Receiver Module
If the key fob does not lock or unlock after you've replaced the battery in the button cell, it is possible that the receiver module is suffering from a fault. The positive side is that this is a simple repair that is inexpensive, you can just disconnect the battery for just a few minutes (first remove the negative cable then press the horn button several times) to remove any remaining electric current, then reconnect it in reverse order e.g. Positive cable first followed by negative.
ESP Warning Light – If the ESP symbol is illuminated, this is normal. It means that you are driving on a terrain that has poor traction. This could be due to gravel, snow or surface water. If the ESP warning light is continuously shining, it is a sign that there is a fault within the system. This can be identified using an iCarsoft i908 Seat OBD Code Reader which will provide a precise fault description.
Dead Coin Battery
A dead coin battery is among the most common reasons for the seat alhambra keys to stop working. The key fob has tiny button cell batteries which keeps it powered. It is recommended to replace it with a replacement with identical in size, voltage and specifications as the original. If you are replacing the battery, ensure that you remove all metal retaining clips from the back of the key fob. Also, make sure that the contact points are clean and free of corrosion.
If the key fob was exposed to water (such as rain or soapy tap water), it is recommended to remove and clean the chip with an electronic cleaner or isopropyl ethanol before installing a brand new battery. The chip is susceptible to moisture and could be permanently damaged. If the key fob still not working after replacing the battery, it might be necessary to replace the entire key fob.
Faulty Receiver Module
If your key fob stopped working after you replaced the battery but it did not help, or if it just stopped working without notice The receiver module could have developed a fault. The receiver module receives radio frequency signals from your key fob's remote and converts them into electrical commands which are then used by other modules in the car.
If the receiver module is damaged it will not take any commands from your remote key fob. In this scenario you'll need to visit a dealer to reprogram your key fob and a new receiver module.
The key fob is covered with rubber to prevent water from getting inside the electronic chip. However, if you submerge the key fob in salty or soapy water, the chip inside may be damaged. You can attempt to clean the chip by rubbing it with isopropyl alcohol or electronic cleaner, however if your key fob still does not work after this, you'll have to buy a new one.
If the keys are in a pair but the receiver module has developed a fault you may try to restart all the on-board electronics by removing the battery at 12 volts for a short period of time. Then, reconnect the battery in reverse order (negative cable first before positive). This resets all the electronic components onboard and bring them back into operation.
Electronic chip that is malfunctioning
The key fob is fitted with a chip that transmits a signal from the key to the receiver module each time the key is used. If the signal does not match the one that the car has stored the immobilizer will turn off and prevent the vehicle from starting. If seat leon key programming purchased does not work and you aren't able to reprogram it, it could be because of an incompatible microchip.
The chip inside the key fob is not an indefinite part of the device and may need to be replaced in order to function again. The best way to do this is to remove the key from its housing and using a pin or needle to connect with each of the retaining clips made of steel. If these are corroded or broken, you will need to replace them in order for the remote control to function. Make sure that any replacement batteries are of the same size, voltage and specifications as the original one.
The Seat Alhambra is a popular and well-designed car however, just like any other vehicle it is not without its challenges. issues with specific components or equipment. Some owners have reported issues with the automatic climate-control system. It is prone to fail and cause problems, and then get stuck in a particular setting. The infotainment system may also fail and freeze the screens.